Are Zero Turn Mowers Good on Hills?

Last updated: November 16, 2020
Published 11:48 pm

Introduction

If you have garden edges or walkways, then it might interest you to know that a Zero-turn mower utilizes flexible caster tires in the front to navigate rapidly around your yard. The Zero turn mower has speeds higher than five mph. These robust mowers speedily trim large lawns, even better than other riding models. According to the consumer reports website, it was gathered that zero-turn mowers could encounter some hiccups on hills, especially the steeper ones.

Accurately Steering Your Zero Turn Mowers

Zero-turn mowers use their rear wheels for steering while the front wheels are casters. For instance, with the steering lever system, turning left involves a right-hand motion, somewhat like a ship navigated using the rudder. Driving in a rough slope with a not so good control of the steering will trigger the mower to shift diagonally to the lawns curves, causing a potential rollover. If you push them too hard, the rear brakes often lead to slipping on hills.

Gently Treading

There is not much traction on caster wheels, allowing zero turn mowers quicker on tight turns. Though helpful for flat lawns, on hills, casters do not provide any stability. The only reliable traction on the grass when you encounter a hill is your rear wheels. They roll against the turf if the wheels lack tread and cause potential slippage down a steep hill. To verify if they have sufficient traction, inspect your wheels and only mow when the grass is dry. Where possible, use large rear wheels to maximize the surface area of the wheels on the floor.

Speeding Isn’t the Best Option.

High-speed mowing is a crucial selling point for zero-turn mowers, however on hills with 15-degree slopes or less, run them gently. For example, as you navigate up and down a hill, ride the zero-turn mower at a steady 4 or 5 mph rate. This constant speed provides wheel traction and safe grass trimming. Once On a slope, skip any sharp turns. The acceleration of the machine on short turns triggers skidding and a potential crash. Before mowing a slope, remove any bagged grass clippings. Excessive weight from a whole bag decreases the power of steering and creates the possibility of slippage on a plateau.

How to navigate Your Zero Turn Mower without Ripping off your Grass

The thought of using a zero-turn mower intimidates many individuals because they are afraid that they might mess up their lawns and destroy their grass. However, if people get too excited or careless when using the machine, this often occurs. This is easily preventable. The environmental conditions when mowing are one of the first things you’ll want to bear in mind. Has it rained lately, or does it look like it will eventually begin to rain? This is a warning that before you mow your lawn, you should wait. For your zero-turn mowers, wet and humid grass causes the lawn too slippery. If you have a conventional riding mower, though you can often get through with these conditions, the caster wheels they have out in front, zero-turn mowers are distinct. In wet and humid conditions, these wheels cannot produce as much traction as conventional riding mower wheels can, which renders them susceptible to crashing over.

If you try to make quick turns, you’ll mostly really see. You’re going to lose control, and you may be able to rip the grass up or fall over. Using a three-point turn is another smart way to stop tearing up your lawn. With a swing turn, some yards are competent enough to withstand turning. However, if your yard is too delicate for this, you would need to add three-point turning to ensure that you get a nice trim without damaging your lawn. You’ll want to move your mower towards the next line of overgrown grass to perform a three-point turn.

Pull back on the levers and back up the mower when you have achieved enough of a turn so that you can reverse. Then change the mower so that you are ideally matched with the uncut grass field and the recently cut grass you have just completed mowing. All you have to do now is straighten your controllers and proceed to this fresh row of grass. There are several objectives for the three-point turn, but perhaps the most relevant is to accomplish the turn when you are in motion rather than rotating in a close and stationary loop.

The concept is that this would help avoid your lawn from being ripped up because it would soften and redirect the strain, which would be caused when you make a swing turn over a wider area of ground. Zero-turn mowers are excellent investments and are reasonably easy to run. As long as you carefully and wisely use this machine, you genuinely can’t have any severe problems tearing your grass or lawn down.

Safety Tips for Using a Zero Turn Mower

When it comes to lawn challenges, inclines and hills tend to be the most difficult, but most are not difficult to mow. Here are some tips to keep you safe when mowing on hills and unlevel terrain, as well as how to make the process safer and a little smoother with Zero Turn Mowers.

  • Always begin by observing safety protocols: It’s necessary to take time to understand your mower and what it can and cannot do when it comes to running a zero-turn mower. You can always read the owner’s operator’s manual, even though you have used a similar mower or owned the same model mower in the past. A zero-turn mower is a powerful machine that needs a little more concentration, unlike using a typical household device or switching on a new computer for the first time.
  • Understand your properties and lawn: In addition to understanding the controls and how the Zero-turn mower operates, it is also necessary to take the time to understand the yard. And it is equally important to understand the properties you and your staff handle if you are a licensed lawn care manager. Pay attention to rough soil, gaps in the lawn, which are not obvious to see, places near water, etc.
  • When mowing hills and inclines, take it slow: The possibility to reduce your mowing time in half is one of the main benefits of owning a Zero Turn Mower. Depending on the design, Zero Turn mowers can travel between 9 and 13 mph. Nevertheless, the very last thing you need to do is go fast when it comes to hills and slopes.

You encourage your mower to get more ground by going slow. It is also recommended that you strive to maintain your speed stable, in addition to keeping your speed below 4-5 mph. This helps not only with stability, but it is also useful for getting a decent cut.

Conclusion

Zero-turn mowers are great for mowing huge lawns; however, if you are to get the best out of them, you need to follow a user guide bound to help you and point you in the right direction. It is recommended to travel at a steady speed if you are unsure about the level of smoothness you have in your yard.